banner01

Products

  • Custom L-Shaped Copper Terminal Lug with Countersunk Holes

    Custom L-Shaped Copper Terminal Lug with Countersunk Holes

    Item Specification
    Product Custom L-shaped copper terminal lug
    Configuration Nominal 90-degree base and upright connection tang with drawing-specific offset
    Construction One-piece component from a suitable copper blank, with CNC finishing
    Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
    Alternative Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr may be reviewed separately
    Material Standard Applicable grade- and stock-form-specific requirements, such as ASTM B187/B187M or ASTM B152/B152M where appropriate
    Overall Length Indicative enquiry range: 15–220 mm
    Base Width Indicative enquiry range: 10–150 mm
    Upright Height Indicative enquiry range: 12–160 mm
    Base and Upright Thickness Indicative enquiry range: 2.5–30.0 mm; equal or unequal thickness according to drawing
    Connection Tang Drawing-specific length, offset, hole position and outer profile
    Hole Options Clearance through-holes, countersunk holes, counterbores or tapped holes
    Countersink Geometry 90-degree, 120-degree or other specified geometry matched to the selected fastener
    Tapped Hole Options Indicative enquiry range: M4–M24, subject to available material and engagement depth
    Hole Pitch and Outline Tolerance Selected-feature targets of ±0.02–0.05 mm, subject to technical review
    Base-to-Upright Perpendicularity Target of 0.02–0.03 mm where feasible; datum and evaluation length must be defined
    Base Contact-Face Flatness Target of 0.02 mm where feasible over the specified contact area
    Contact-Surface Roughness Ra 0.4–0.8 μm may be specified as a finishing target
    Hardness An enquiry target of 85–120 HV may be reviewed for suitable grades and material conditions
    Electrical Conductivity A target of ≥98% IACS may be specified for suitable pure copper grades and conditions, subject to agreed testing
    Surface Options Clean bare copper, compatible anti-tarnish treatment, silver plating, tin plating or nickel plating
    Edge Features Rounded corners, chamfers and clearance reliefs according to drawing
    Electrical Rating Determined by the completed connection and equipment verification
    Documentation Material and inspection documents agreed before order placement
  • Custom Dual-Stud Copper Blade Contact Terminal

    Custom Dual-Stud Copper Blade Contact Terminal

    Item Specification
    Product Custom dual-stud copper blade contact terminal
    Main Geometry Rounded blade head, central flange and two stepped threaded stems
    Threaded Features External stud threads with axial internal tapped holes
    Construction Monoblock machining from a common blank where specified
    Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
    Alternative Materials Silver-bearing copper, tellurium copper or CuCrZr may be reviewed separately; conductivity and mechanical properties differ
    Material Standard Selected according to grade and starting form; applicable rod, plate or forging specifications agreed before production
    Overall Length Indicative enquiry range: 30–260 mm
    Overall Width Indicative enquiry range: 15–140 mm
    Overall Height Indicative enquiry range: 25–180 mm
    Blade Thickness According to the mating contact and approved drawing
    Stud Center Distance Drawing-specific
    External Metric Threads Indicative enquiry range: M10–M48
    Internal Metric Threads Indicative enquiry range: M6–M30
    Alternative Threads UN/UNF or other specified forms subject to drawing review
    Thread Fit Metric 6g/6H or unified 2A/2B where specified; coating allowance must be considered
    Blade Thickness and Stud Pitch Tolerance Selected-feature targets of ±0.015–0.03 mm, subject to technical review
    Internal-to-External Thread Alignment Target of 0.02 mm where feasible; datum and geometric control to be defined on the drawing
    Stud Perpendicularity Target of 0.02 mm where feasible; reference surface and evaluation length must be specified
    Blade Contact-Face Roughness Ra 0.2–0.4 μm may be specified as a finishing target
    Hardness An enquiry target of 85–125 HV may be reviewed for suitable grades and tempers
    Electrical Conductivity A target of ≥98% IACS may be specified for suitable pure copper grades and conditions, subject to agreed testing
    Surface Options Bare copper, compatible anti-tarnish treatment, selective or full silver plating, tin plating or nickel plating
    Silver Coating Thickness A 10–30 μm range may be reviewed; coating type, hardness, underlayer and coverage require separate specification
    Current and Voltage Ratings Established by the completed equipment design and applicable verification
    Supply Condition Machined component, with agreed finishing and inspection
  • Cold-Drawn Multi-Groove Copper Profile for Heat Pipe Baseplates

    Cold-Drawn Multi-Groove Copper Profile for Heat Pipe Baseplates

    Item Specification
    Product Cold-drawn multi-groove copper profile
    Cross-Section Multiple parallel round-bottom open grooves with intervening ribs and a continuous flat-backed base
    Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
    Alternative Grade Designations Cu-ETP, Cu-OF or Chinese copper grades can be reviewed against their specified standards; equivalence must be confirmed
    Overall Width Indicative enquiry range: 15–260 mm
    Overall Thickness Indicative enquiry range: 3–45 mm
    Groove Count Indicative range: 2–24; uniform or drawing-specific arrangements
    Groove Radius Indicative enquiry range: R1.5–R20 mm
    Tube Sizes for Design Review Nominal tube diameters of approximately Ø3–Ø40 mm; actual fit requires tube and joint specifications
    Groove Pitch According to the approved drawing
    Remaining Base Wall Nominal thickness beneath the grooves to be specified separately on the drawing
    Cut Blank Length Indicative enquiry range: 20–1,200 mm
    Straight Bar Length Indicative enquiry range: 1,000–6,000 mm
    Groove Radius and Pitch Tolerance Selected-feature targets of ±0.015–0.03 mm, subject to technical review
    Remaining Base Wall Tolerance Selected-feature target of ±0.02 mm, subject to nominal wall thickness and agreed measurement method
    Back-Surface Flatness Target of 0.02–0.04 mm over an agreed 100 mm span; full-length requirements quoted separately
    Groove Surface Roughness Ra 0.2–0.4 μm may be reviewed as a finishing target for specified surfaces
    Temper H02, H04 or O60 where applicable to the selected material and product standard
    Electrical Conductivity A target of ≥98% IACS may be specified for suitable grades and conditions, subject to agreed testing
    Thermal Conductivity Grade-, condition- and temperature-dependent; numerical requirements require separate confirmation
    Surface Options Bare copper, compatible anti-tarnish treatment, nickel, tin or silver plating by agreement
    Secondary Processing Cutting, back milling, drilling, tapping, deburring and drawing-specific machining
    Supply Condition Profile stock, cut blanks or further-machined components
    Standards and Documentation Applicable material standard, acceptance criteria and documentation agreed before production
  • Cold-Drawn Three-Tier Stepped Copper Profile

    Cold-Drawn Three-Tier Stepped Copper Profile

    Item Specification
    Product Name Cold-Drawn Three-Tier Stepped Copper Profile
    Cross-Section Raised central land, bilateral intermediate shoulders, thinner outer wings and a flat back
    Standard Geometry Symmetrical three-tier section with two step transitions on each side
    Custom Geometry Step widths, heights, root radii and asymmetric variants subject to drawing review
    Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
    Other Grade Designations Cu-ETP/CW004A, Cu-OF/CW008A, T2, TU1 or TU2 may be reviewed under their respective specifications; equivalence is not assumed
    Reference Standards ASTM B187/B187M or EN 13605 where applicable to the ordered grade and form; final requirements per purchase specification
    Overall Width Indicative range: 18–280 mm
    Total Center Thickness Indicative range: 4–50 mm
    Outer Wing Thickness Indicative range: 1–15 mm
    Cut Blank Length Indicative range: 20–1,200 mm
    Straight Bar Length Indicative range: 1,000–6,000 mm
    Step Height and Thickness Tolerance Selected-feature targets of ±0.015–0.04 mm, subject to review; final machining may be required
    Face Parallelism Target of 0.02 mm for individually specified step faces relative to the back datum, subject to measurement span and process confirmation
    Left-to-Right Symmetry Target of 0.03 mm, with center reference and inspection method defined by drawing
    Back Flatness Target of 0.02–0.04 mm over an agreed 100 mm span; full-length flatness specified separately
    Surface Roughness Ra ≤0.4 μm target on nominated functional surfaces, subject to finishing requirements
    Temper H02, H04 or O60 where applicable to the selected material standard
    Hardness Indicative 85–120 HV for selected cold-worked conditions; annealed material specified separately
    Electrical Conductivity A target of ≥98% IACS may be specified for suitable pure copper grades and conditions, subject to verification
    Thermal Conductivity Required value, material condition and test temperature to be agreed for thermal applications
    Surface Options Uncoated copper, specified anti-tarnish treatment, nickel plating, silver plating or tin plating
    Secondary Processing Cutting, drilling, tapping, local milling, deburring and specified surface finishing
    Supply Condition Profile stock, cut blanks or drawing-based finished components
    Documentation Material certificates and agreed dimensional, conductivity or coating inspection records
    Packaging Protective separation and packing appropriate to surface condition, wing geometry and shipment requirements
  • Cold-Drawn Hook-Shaped Copper Profile Block

    Cold-Drawn Hook-Shaped Copper Profile Block

    Item Specification
    Product Name Cold-Drawn Hook-Shaped Copper Profile Block
    Cross-Section Extended flat connection leg, enlarged hooked head, curved inner transition and concave relief groove
    Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
    Other Grade Designations Cu-ETP/CW004A, Cu-OF/CW008A, T2, TU1 or TU2 may be reviewed against their respective specifications; grades are not automatically interchangeable
    Reference Standards ASTM B187/B187M or EN 13605 where applicable to the ordered grade and product form; requirements confirmed in the purchase specification
    Envelope Width × Height Indicative range: 15 × 15 mm to 180 × 180 mm; feasible width and height combinations require drawing review
    Connection Leg Thickness Indicative range: 3–40 mm
    Cut Block Length Indicative range: 12–800 mm
    Straight Bar Length Indicative range: 1,000–6,000 mm, subject to section and handling requirements
    Linear and Wall Thickness Tolerance Selected-feature targets of ±0.03–0.06 mm, subject to drawing and process confirmation
    Curved Contour Accuracy Profile-of-a-line tolerance up to 0.05 mm may be reviewed for specified sections, datums and inspection conditions
    Connection Leg Flatness Target of 0.03 mm may be reviewed over an agreed measurement span
    Surface Roughness Ra 0.4–0.8 μm target on specified functional surfaces, subject to manufacturing route
    Temper H02, H04 or O60 where applicable to the selected material standard
    Hardness Indicative 85–125 HV for selected cold-worked conditions; not applicable to all grades or tempers
    Electrical Conductivity A target of ≥98% IACS may be specified for appropriate pure copper grades and conditions, subject to verification
    Surface Options Uncoated copper, specified anti-tarnish treatment, selective silver plating or tin plating
    Silver Plating Thickness Indicative enquiry range: 5–30 μm; thickness, undercoat and coated areas defined by drawing
    Secondary Processing Cutting, drilling, tapping, machining, deburring and application-specific finishing
    Supply Condition Profile stock, cut blanks or drawing-based finished parts
    Documentation Material certificates, dimensional reports and additional test records as agreed
    Packaging Protective separation and packing selected to protect edges, surfaces and any plated areas
  • Cold-Drawn Stepped T-Profile Pure Copper Bar

    Cold-Drawn Stepped T-Profile Pure Copper Bar

    Item Specification
    Product Type Stepped T-profile copper bar with rectangular tenon and bilateral flanges
    Material Options C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, or TU2, specified under the selected material standard
    Alternative Alloys C10400/C10700 silver-bearing copper or C18150 CuCrZr may be reviewed separately; properties differ from pure copper
    Applicable Standards ASTM B187/B187M or EN 13605 where applicable to the grade and product form; other specifications by agreement
    Overall Width Indicative enquiry range: 6–180 mm
    Overall Height Indicative enquiry range: 4–90 mm
    Tenon Width Indicative enquiry range: 2.5–120 mm
    Flange Thickness Indicative enquiry range: 1–25 mm
    Flange Configuration Equal or unequal side widths, according to drawing
    Cut Segment Length Approximately 15–1,500 mm
    Straight Bar Length Approximately 1,000–6,000 mm
    Coil Supply Subject to section size, temper, bend radius, and production feasibility
    Tenon Width and Flange Thickness Tolerance Indicative target: ±0.015–0.03 mm on agreed features
    Top-to-Bottom Parallelism Indicative target: ≤0.02 mm over a specified measurement span
    Straightness Indicative target: ≤0.25 mm/m under an agreed measurement method
    Internal Root Radius Indicative target: 0.15–0.25 mm, subject to tooling and section geometry
    Surface Roughness Indicative target: Ra 0.2–0.4 μm on designated surfaces
    Temper H02, H04, O60, or another agreed condition where applicable
    Hardness Indicative 85–125 HV for selected work-hardened conditions; not applicable to every grade or temper
    Electrical Conductivity Grade- and temper-dependent; a target such as ≥98% IACS requires confirmation for the selected material
    Surface Options Cleaned copper, bright finish, anti-tarnish treatment, silver plating, tin plating, or nickel coating
    Secondary Processing Cutting, drilling, tapping, milling, chamfering, deburring, and application-specific finishing
  • Cold-Drawn Compact Double-Rabbet Z-Section Pure Copper Terminal Block

    Cold-Drawn Compact Double-Rabbet Z-Section Pure Copper Terminal Block

    Item Specification
    Product Type Compact double-rabbet Z-section pure copper terminal block or busbar jumper
    Material Options C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, TU2
    Optional Materials C10400, C10700, or C18150 may be reviewed separately for specific thermal, wear, or softening-resistance requirements
    Applicable Standards ASTM, EN, JIS, GB/T, or customer drawing, depending on grade and product form
    Section Configuration Symmetrical double-rabbet Z-profile or asymmetric offset-rabbet configuration
    Overall Width Indicative enquiry range: 8–160 mm
    Overall Height Indicative enquiry range: 6–120 mm
    Rabbet or Step Depth Approximately 1.5–50 mm, subject to section design
    Cut Block Length Approximately 8–800 mm
    Straight Bar Length Approximately 1,000–6,000 mm
    Coil Supply Possible only when section size, temper, and forming feasibility allow
    Step Thickness Tolerance Indicative target: ±0.015–0.04 mm
    Step Height Difference Confirmed by drawing and inspection method
    Four-Plane Parallelism Indicative target: ≤0.02 mm
    Rabbet Wall Verticality Indicative target: ≤0.02 mm
    Root Radius Approximately R0.15–0.30 mm when feasible
    Surface Roughness Indicative target: Ra 0.4–0.8 μm
    Temper H02, H04, or O60 according to forming and assembly requirements
    Hardness Indicative range for selected hard tempers: approximately 85–125 HV
    Conductivity Confirmed by grade, temper, standard, and test method; high-conductivity copper grades may be specified for electrical use
    Surface Finish Bright copper, cleaned copper, anti-tarnish treatment, silver plating, tin plating, or nickel plating
    Secondary Operations Cutting, drilling, tapping, milling, deburring, slotting, brazing, and plating
    Inspection Documents Dimensional report, material certificate, conductivity or hardness report, and additional documents when required
    Customization 2D drawing, 3D model, sample, or detailed section sketch accepted for review
  • Cold-Drawn Asymmetric Offset Inverted T-Section Pure Copper Profile Bar

    Cold-Drawn Asymmetric Offset Inverted T-Section Pure Copper Profile Bar

    Specification Details
    Product Name Cold-Drawn Asymmetric Offset Inverted T-Section Pure Copper Profile Bar
    Product Type Unequal-flange conductor rail, keyed copper contact track or asymmetric copper profile
    Material Options C11000 ETP, C10200 OFC, C10100 OFHC, Cu-ETP, Cu-OF, T2, TU1 and TU2
    Optional Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr, subject to technical review
    Applicable Standards ASTM B187/B187M, ASTM B152/B152M, ASTM B133, EN 13601, EN 13605, JIS H3140, JIS H3250 and GB/T 5585
    Manufacturing Route Continuous extrusion, asymmetric cold drawing, multi-roll straightening and precision cutting
    Overall Base Width Approximately 5.0–150.0 mm
    Total Profile Height Approximately 4.0–100.0 mm
    Flange Configuration Narrow micro-lip plus wider mounting flange, with W1 not equal to W2
    Central Boss Square or rectangular conductive boss; dimensions according to drawing
    Optional Geometry Unequal-thickness step flanges, offset boss, locating lip, keyway or custom retaining features
    Supply Form Cut segments approximately 15–1,500 mm, bars approximately 1,000–6,000 mm or coil supply when feasible
    Boss and Flange Tolerance Typical target ±0.015–0.03 mm
    Full-Length Straightness/Camber Typical target ≤0.2–0.3 mm per meter
    Base Flatness Typical target ≤0.02 mm
    Root Radius Typical target R ≤0.15–0.25 mm
    Surface Roughness Typical target Ra ≤0.2–0.4 μm
    Temper Options H02, H04 or O60
    Indicative Hardness Approximately 90–125 HV for selected hard-tempers
    Conductivity Target up to or above 98% IACS for applicable grades; verify by grade and test method
    Surface Finish Bright copper, mirror-bright copper, anti-tarnish passivation, silver plating, tin plating or nickel plating
    Silver Plating Full or selective plating according to the contact area; ASTM B700 can be referenced
    Tin Plating Available according to customer requirement; ISO 2093 can be referenced
    Nickel Plating Available according to customer requirement; ISO 1456 can be referenced
    Secondary Operations Drilling, tapping, slotting, chamfering, deburring, marking and cut-to-length processing
    Inspection Documents MTC, chemical analysis, conductivity, hardness, dimensional and plating reports when specified
    Final Requirement Final dimensions, asymmetry, straightness and tolerances are subject to drawing review
  • Cold-Drawn Bulb-Head and Cylindrical-Boss Pure Copper Contact Profile

    Cold-Drawn Bulb-Head and Cylindrical-Boss Pure Copper Contact Profile

    Specification Details
    Product Name Cold-Drawn Bulb-Head and Cylindrical-Boss Pure Copper Contact Profile
    Product Type Tulip-contact receiver, pivot blade, stationary contact profile or retaining-rib copper block
    Material Options C11000 ETP, C10200 OFC, C10100 OFHC, Cu-ETP, Cu-OF, T2, TU1 and TU2
    Optional Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr, subject to technical review
    Applicable Standards ASTM B187/B187M, ASTM B152/B152M, ASTM B133, EN 13601, EN 13605, JIS H3140, JIS H3250 and GB/T 5585
    Manufacturing Route Continuous casting, hot extrusion, complex-contour cold drawing, straightening and precision cutting
    Total Profile Height Approximately 20–220 mm
    Overall Profile Width Approximately 10–180 mm
    Central Cylindrical Boss Approximately Ø8–100 mm
    Thin Contact Blade Thickness Approximately 2.0–25.0 mm
    Profile Features Semi-cylindrical bulb head, central boss, stop shoulders, thin blade and retaining ribs
    Cut Block Length Approximately 15–1,000 mm
    Bar Length Approximately 1,000–6,000 mm
    Diameter Tolerance Typical target ±0.02–0.05 mm
    Cylindricity and Symmetry Typical target ≤0.03 mm
    Blade Flatness Typical target ≤0.03 mm
    Blade Perpendicularity Typical target ≤0.03 mm
    Contact-Face Roughness Typical target Ra ≤0.2–0.4 μm
    Temper Options H02, H04 or O60, subject to grade and application
    Indicative Hardness Approximately 90–125 HV for selected hard-tempers
    Conductivity Target up to or above 98% IACS for applicable grades; verify by grade and test method
    Surface Finish Bright copper, anti-tarnish passivation, full or selective silver plating, tin plating or nickel plating
    Silver Plating Approximately 10–30 μm when specified; ASTM B700 can be referenced
    Tin Plating Available according to customer requirement; ISO 2093 can be referenced
    Nickel Plating Available according to customer requirement; ISO 1456 can be referenced
    Secondary Operations Drilling, tapping, slotting, trimming, chamfering, deburring and selective surface finishing
    Inspection Documents MTC, chemical analysis, conductivity, hardness, dimensional and plating reports when specified
    Final Requirement All dimensions, tolerances and performance values are subject to the approved drawing and technical review
  • Solid Rectangular Copper Conductive Block

    Solid Rectangular Copper Conductive Block

    Specification Details
    Product Name Solid Rectangular Pure Copper Conductive Block
    Product Type Full-flat block, stepped block, half-lap splice block or rabbeted copper terminal block
    Material Options C11000 ETP, C10200 OFC, C10100 OFHC, Cu-ETP, Cu-OF, T2, TU1 and TU2
    Optional Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr, subject to technical review
    Applicable Standards ASTM B187/B187M, ASTM B152/B152M, ASTM B133, EN 13601, EN 13605, JIS H3140, JIS H3250 and GB/T 5585
    Manufacturing Route Continuous casting, extrusion, cold drawing, cold sawing and precision machining
    Overall Profile Width Approximately 15–260 mm
    Overall Thickness Approximately 6–80 mm
    Shallow Step Depth Approximately 1–5 mm
    Deep Half-Lap Step Depth Approximately 5–40 mm
    Cut Block Length Approximately 20–1,000 mm
    Bar Length Approximately 1,000–6,000 mm
    High/Low Face Thickness Tolerance Typical target ±0.02–0.05 mm
    Upper/Lower Face Parallelism Typical target ≤0.02 mm
    90-Degree Step Verticality Typical target ≤0.02 mm
    Root Radius Typical target R ≤0.15–0.30 mm
    Surface Roughness Typical target Ra ≤0.4 μm on specified functional surfaces
    Temper Options H02, H04 or O60, subject to material and drawing
    Indicative Hardness Approximately 85–125 HV for selected hard-tempers
    Conductivity Target up to or above 98% IACS for applicable grades; verify by grade and test method
    Surface Finish Bright copper, anti-tarnish passivation, silver plating, tin plating or nickel plating
    Silver Plating Approximately 5–30 μm when specified; ASTM B700 can be referenced
    Tin Plating Available according to customer requirement; ISO 2093 can be referenced
    Nickel Plating Available according to customer requirement; ISO 1456 can be referenced
    Secondary Operations Drilling, tapping, milling, slotting, chamfering, deburring and marking
    Inspection Documents MTC, chemical analysis, conductivity, hardness, dimensional and plating reports when specified
    Final Requirement Dimensions, tolerances and performance must be confirmed by the approved drawing and technical review
  • Pure Copper Knife Contact Blade

    Pure Copper Knife Contact Blade

    Specification Details
    Product Name Pure Copper Inverted T-Section Guided Knife Contact Blade
    Product Type Custom conductive contact blade / stationary knife contact
    Material Options C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1 or TU2
    Optional Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr, subject to technical review
    Material Standards ASTM B187/B187M, ASTM B152/B152M, ASTM B133, EN 13601, EN 13605, JIS H3140, JIS H3250 or GB/T 5585
    System-Level References IEC 62271 and IEC 61439 where applicable to the complete switchgear design
    Manufacturing Route Profile extrusion, cold drawing, forging, CNC machining or combined production route
    Base Flange Width Approximately 15–180 mm
    Blade Height Approximately 20–200 mm
    Blade/Web Thickness Approximately 3–35 mm
    Base Flange Thickness Approximately 2.5–30 mm
    Cut Length Approximately 20–800 mm
    Standard Bar Length Approximately 1,000–6,000 mm
    Tip Geometry Symmetrical wedge, double-beveled tip, single-radius bullet tip or full-radius bullnose
    Edge Treatment Sharp functional lead-in edge, controlled radius or rounded edge according to drawing
    Temper H02, H04 or other customer-specified condition
    Indicative Hardness Approximately 95–125 HV, subject to grade and temper
    Conductivity Target up to or above 98% IACS for applicable pure copper grades; verify by grade and test method
    Blade Thickness Tolerance Typical target ±0.02–0.04 mm
    Blade-to-Base Perpendicularity Typical target ≤0.02–0.03 mm
    Contact-Face Roughness Typical target Ra ≤0.2–0.4 μm
    Surface Options Bright copper, anti-tarnish treatment, silver plating, tin plating, nickel plating or anti-galling coating
    Silver Plating Approximately 10–30 μm when specified; ASTM B700 or customer specification
    Tin Plating Available according to order requirement; ISO 2093 can be referenced
    Nickel Plating Available according to application; ISO 1456 can be referenced
    Inspection Documents MTC, chemical analysis, conductivity, hardness, dimensional report and plating records when specified
    Final Requirement All dimensions and tolerances are subject to the approved 2D/3D drawing and manufacturability review
  • Cold-Drawn Pure Copper Inverted T-Profile Busbar Series

    Cold-Drawn Pure Copper Inverted T-Profile Busbar Series

    Item Specification
    Product Cold-Drawn Pure Copper Inverted T-Profile Busbar Series
    Product Forms T-section busbar, knife contact blade, T-bar connector or custom copper profile
    Available Grades C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1 and TU2
    Optional Specialty Grades C10400/C10700 silver-bearing copper or C18150 CuCrZr subject to technical review
    Applicable Standards ASTM B187/B187M, ASTM B152/B152M, ASTM B133, EN 13601, EN 13605, JIS H3140, JIS H3250, GB/T 5585 or agreed specification
    Manufacturing Route Hot extrusion, precision cold drawing, multi-roll straightening and cold sawing
    Base Flange Width × Total Height Indicative range: 12–220 mm × 15–220 mm
    Indicative Current Class Approximately 400–6300 A; confirm by electrical and thermal design
    Web and Flange Thickness Indicative range: 2.0–45.0 mm
    Wall Configuration Equal-wall, thick-web/thin-base, thin-web/thick-base or asymmetric offset
    Top Edge Geometry Full-radius bullnose or sharp flat-top
    Supply Length Cut segments approximately 15–1200 mm; bars approximately 1000–6000 mm
    Wall Thickness Tolerance Indicative range: ±0.02–0.05 mm
    Web-to-Base Perpendicularity Indicative value: ≤0.02–0.04 mm
    Root Radius Indicative range: R ≤0.2–0.5 mm
    Electrical Conductivity Target values from 98% IACS for applicable grades; confirm by grade and test method
    Surface Roughness Indicative value: Ra ≤0.4 μm
    Temper H02/H04 hard temper or O60 annealed condition
    Surface Options Bright copper, anti-tarnish passivation, silver plating, tin plating or nickel plating
    Silver Plating Full or selective plating, approximately 10–30 μm when specified
    Secondary Operations Drilling, tapping, punching, chamfering, deburring and CNC machining
    Inspection Chemical composition, conductivity, hardness, profile dimensions, perpendicularity, flatness and surface inspection
    Documentation Material certificates, dimensional reports and process records according to order requirements