Cold-Drawn Multi-Groove Copper Profile for Heat Pipe Baseplates

Short Description:

Item Specification
Product Cold-drawn multi-groove copper profile
Cross-Section Multiple parallel round-bottom open grooves with intervening ribs and a continuous flat-backed base
Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
Alternative Grade Designations Cu-ETP, Cu-OF or Chinese copper grades can be reviewed against their specified standards; equivalence must be confirmed
Overall Width Indicative enquiry range: 15–260 mm
Overall Thickness Indicative enquiry range: 3–45 mm
Groove Count Indicative range: 2–24; uniform or drawing-specific arrangements
Groove Radius Indicative enquiry range: R1.5–R20 mm
Tube Sizes for Design Review Nominal tube diameters of approximately Ø3–Ø40 mm; actual fit requires tube and joint specifications
Groove Pitch According to the approved drawing
Remaining Base Wall Nominal thickness beneath the grooves to be specified separately on the drawing
Cut Blank Length Indicative enquiry range: 20–1,200 mm
Straight Bar Length Indicative enquiry range: 1,000–6,000 mm
Groove Radius and Pitch Tolerance Selected-feature targets of ±0.015–0.03 mm, subject to technical review
Remaining Base Wall Tolerance Selected-feature target of ±0.02 mm, subject to nominal wall thickness and agreed measurement method
Back-Surface Flatness Target of 0.02–0.04 mm over an agreed 100 mm span; full-length requirements quoted separately
Groove Surface Roughness Ra 0.2–0.4 μm may be reviewed as a finishing target for specified surfaces
Temper H02, H04 or O60 where applicable to the selected material and product standard
Electrical Conductivity A target of ≥98% IACS may be specified for suitable grades and conditions, subject to agreed testing
Thermal Conductivity Grade-, condition- and temperature-dependent; numerical requirements require separate confirmation
Surface Options Bare copper, compatible anti-tarnish treatment, nickel, tin or silver plating by agreement
Secondary Processing Cutting, back milling, drilling, tapping, deburring and drawing-specific machining
Supply Condition Profile stock, cut blanks or further-machined components
Standards and Documentation Applicable material standard, acceptance criteria and documentation agreed before production

Product Detail

Product Tags

Video

Short Description

Custom multi-groove copper profiles featuring parallel round-bottom open grooves and a continuous flat-backed base. Supplied as straight lengths or cut blanks for heat pipe baseplates, thermal spreaders and drawing-specific conductive components. Material options include C11000, C10200 and C10100, with groove geometry, temper, machining and surface treatment specified to suit the intended assembly. Final dimensions, tolerances and inspection requirements are confirmed against the approved drawing.

Multi-Groove Copper Profile Overview

A multi-groove copper profile combines multiple longitudinal concave grooves with a continuous copper base. The open grooves can provide seating geometry for heat pipes or other tubular components, while the flat back provides a reference surface for subsequent machining or assembly.

Cymber Metal supplies drawing-based profiles using selected pure copper materials. Groove count, radius, pitch, base thickness and cut length can be developed around the intended tube arrangement and available installation space.

Material selection should account for conductivity, forming requirements and the proposed joining process. For assemblies requiring an oxygen-free copper option, C10200 copper can be reviewed alongside C10100 and C11000.

This product is an open-grooved profile or component blank. It is not, by itself, a sealed heat pipe, a pressure-tight cold plate or a validated cooling assembly.

Key Features

Feature Practical Value
Parallel Round-Bottom Grooves Provides a repeatable seating layout for compatible heat pipes or tubular components
Continuous Copper Base Provides material beneath the grooves for heat spreading or current conduction, subject to the final design
Flat Back Geometry Supports defined machining datums and assembly interfaces
Custom Groove Layout Allows groove count, pitch, radius and outer dimensions to follow the intended component arrangement
Near-Net Profile Supply Can reduce material removal compared with machining the complete cross-section from solid stock
Secondary Machining Options Enables mounting holes, threads, finished contact faces and other drawing-specific features
Selectable Surface Treatment Allows surface protection or interface requirements to be reviewed against the joining and service conditions

Manufacturing & Quality Control

Manufacturing Process

Stage Process and Control
Drawing and Application Review Confirm groove geometry, tube arrangement, base wall thickness, datums, critical dimensions and intended joining method
Material Selection Select the copper grade, temper and incoming material requirements for the intended forming and assembly processes
Profile Forming Establish a suitable near-net forming route, including custom copper profile extrusion where appropriate
Cold Drawing and Dimensional Refinement Use controlled drawing operations where suitable to refine the cross-section; pass sequence depends on profile complexity and material condition
Intermediate Annealing Apply annealing where required by the forming route and final temper specification
Straightening and Cutting Control straightness and supply the agreed bar lengths or cut blanks
Secondary Machining Use drawing-based precision machining services for back faces, holes, threads and additional features
Surface Treatment Apply the specified cleaning, protection or plating process, with joining and thermal-interface compatibility reviewed beforehand
Packaging Protect groove edges, contact surfaces and finished faces against handling damage during shipment

Quality Control

Inspection scope and acceptance criteria are agreed for each order. Further information is available on our quality assurance page.

Inspection Item Verification and Acceptance Basis
Material Identification Review material certificates and maintain the agreed batch identification
Chemical Composition Verify against the specified grade using suitable analytical methods; oxygen-content requirements need a dedicated appropriate method
Cross-Section Dimensions Check width, thickness, groove radius, pitch and rib geometry using suitable dimensional equipment
Remaining Base Wall Measure the material beneath the grooves against the specified nominal thickness and tolerance
Flatness and Straightness Inspect against agreed datums, measurement spans and support conditions
Groove Surface Condition Check for relevant surface defects; measure roughness where specified
Tube-to-Groove Fit Assess against the actual tube dimensions, ovality and intended joint clearance where assembly-fit verification is ordered
Conductivity Test where required, with the method, material condition and acceptance value defined in advance
Plating and Finish Inspect coating type, thickness, coverage and specified functional requirements where applicable
Documentation Supply agreed material and inspection records; EN 10204 3.1 documentation or third-party inspection must be confirmed before order placement

Typical Applications

Application Typical Use Design Considerations
Heat Pipe Baseplates Grooved copper blanks for parallel heat pipe arrangements in CPU, GPU and server cooling assemblies Actual tube diameter, ovality, joint clearance, contact resistance and completed assembly performance
Power Electronics Cooling Heat-spreading components for inverters, power modules and related thermal assemblies Heat load, mounting flatness, interface materials and thermal cycling
High-Power Laser Equipment Drawing-specific copper bases incorporating multiple tube seats Local heat flux, interface geometry and compatibility with the joining process
Embedded-Tube Cold Plate Bases Open-grooved bases for subsequent tube installation and assembly The profile is not pressure-tight; sealing, pressure testing and leak testing apply to the completed assembly
Custom Electrical Conductor Profiles Fluted or grooved copper bars for drawing-specific electrical equipment Effective conductive cross-section, connection design, clearances and verified temperature rise
Multi-Contact Conductor Rails Custom profiles for equipment requiring repeated longitudinal contact features Contact pressure, wear, plating, alignment and operating conditions

FAQ

Can the groove count, radius and pitch be customized?

Yes. These features can be reviewed against your drawing, together with overall width, rib dimensions and remaining base wall thickness. Feasibility depends on the complete cross-section.

Which copper grades can be specified?

Material options include C11000, C10200 and C10100. The grade and temper should be selected around conductivity, forming, joining and service requirements.

Will a nominal tube diameter automatically fit the groove?

No. Fit depends on the actual tube outside diameter, ovality, groove geometry and intended joining clearance. Nominal tube size alone is insufficient to define the interface.

Is this a finished liquid cold plate or heat pipe?

No. It is an open-grooved profile or blank. Tube installation, joining, sealing and assembly-level testing are separate operations unless expressly included in the order.

Are the listed tolerances available on every size?

No. They are selected-feature enquiry targets. Achievable tolerances depend on profile dimensions, material, temper, length, datums and the agreed inspection method.

Does the grooved shape guarantee better cooling performance?

No. Performance depends on the complete thermal path, including tube installation, joint quality, contact resistance, airflow or coolant conditions and operating temperature.

Can this profile be used as an electrical conductor?

It can be reviewed for drawing-specific conductive applications. Current capacity must account for the remaining copper cross-section, connections, cooling conditions and validated temperature rise.

What inspection documents can be supplied?

Material certificates and dimensional inspection records can be agreed with the order. Conductivity reports, additional testing, EN 10204 3.1 documentation and third-party inspection require advance confirmation.

Request a Quote

Please provide a dimensioned cross-section and the following information so we can review the profile and quotation requirements.

Required Information Details to Provide
Drawing PDF drawing and, where available, a STEP or other suitable CAD file
Material and Temper Required copper grade, applicable standard and temper
Overall Dimensions Width, thickness, profile length and cut blank dimensions
Groove Geometry Groove count, radius, depth, pitch, rib dimensions and remaining base wall
Tube Interface Actual tube OD, tolerance, ovality and intended joint clearance where applicable
Assembly Process Soldering, brazing, bonding, mechanical retention or another specified method
Critical Requirements Dimensional tolerances, datums, flatness, straightness and surface roughness
Surface Treatment Bare copper, anti-tarnish treatment or specified plating system
Order Quantity Trial quantity, batch quantity and expected repeat demand
Inspection and Documents Required tests, inspection frequency, certificates and third-party inspection scope

Contact Cymber Metal with your drawing, quantity and intended application to request a technical review and quotation.


  • Previous:
  • Next:

  • Write your message here and send it to us