Custom L-Shaped Copper Terminal Lug with Countersunk Holes

Short Description:

Item Specification
Product Custom L-shaped copper terminal lug
Configuration Nominal 90-degree base and upright connection tang with drawing-specific offset
Construction One-piece component from a suitable copper blank, with CNC finishing
Material Options C11000 ETP copper, C10200 oxygen-free copper or C10100 oxygen-free electronic copper
Alternative Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr may be reviewed separately
Material Standard Applicable grade- and stock-form-specific requirements, such as ASTM B187/B187M or ASTM B152/B152M where appropriate
Overall Length Indicative enquiry range: 15–220 mm
Base Width Indicative enquiry range: 10–150 mm
Upright Height Indicative enquiry range: 12–160 mm
Base and Upright Thickness Indicative enquiry range: 2.5–30.0 mm; equal or unequal thickness according to drawing
Connection Tang Drawing-specific length, offset, hole position and outer profile
Hole Options Clearance through-holes, countersunk holes, counterbores or tapped holes
Countersink Geometry 90-degree, 120-degree or other specified geometry matched to the selected fastener
Tapped Hole Options Indicative enquiry range: M4–M24, subject to available material and engagement depth
Hole Pitch and Outline Tolerance Selected-feature targets of ±0.02–0.05 mm, subject to technical review
Base-to-Upright Perpendicularity Target of 0.02–0.03 mm where feasible; datum and evaluation length must be defined
Base Contact-Face Flatness Target of 0.02 mm where feasible over the specified contact area
Contact-Surface Roughness Ra 0.4–0.8 μm may be specified as a finishing target
Hardness An enquiry target of 85–120 HV may be reviewed for suitable grades and material conditions
Electrical Conductivity A target of ≥98% IACS may be specified for suitable pure copper grades and conditions, subject to agreed testing
Surface Options Clean bare copper, compatible anti-tarnish treatment, silver plating, tin plating or nickel plating
Edge Features Rounded corners, chamfers and clearance reliefs according to drawing
Electrical Rating Determined by the completed connection and equipment verification
Documentation Material and inspection documents agreed before order placement

Product Detail

Product Tags

Video

Short Description

Custom L-shaped copper terminal lug featuring a perpendicular base and offset connection tang, with through-holes and countersunk mounting features specified to the assembly drawing. A near-net copper angle blank with CNC finishing can provide a one-piece connection between conductors arranged at 90 degrees. Material options include C11000, C10200 and C10100, with customized dimensions, hole patterns, contact surfaces and optional plating. Final tolerances and inspection requirements are confirmed before production.

L-Shaped Copper Terminal Lug Overview

An L-shaped copper terminal lug provides a bolted conductive connection between components arranged on perpendicular planes. This offset design combines a mounting base with a projecting connection tang, allowing the hole layout and terminal position to accommodate drawing-specific equipment interfaces.

The illustrated component incorporates rounded outer edges, a connection through-hole and countersunk mounting features. Correctly matched countersunk fasteners can provide recessed or flush screw-head seating, subject to the specified head angle, diameter and countersink depth.

Cymber Metal supports custom terminals using selected pure copper materials. C11000 ETP copper is one option, while C10200 oxygen-free copper and C10100 can be reviewed where an oxygen-free grade is required.

A suitable near-net L-section blank can reduce machining compared with producing the complete angle from a solid rectangular block. The selected route and final corner geometry must still satisfy the required conductive cross-section, mechanical loads and dimensional criteria.

This is a solid bolted connection component, not a cable-crimp lug or an insulating support. Current capacity, dielectric suitability and equipment compatibility depend on the complete assembly.

Key Features

Feature Practical Value
Right-Angle Connection Geometry Provides a conductive transition between perpendicular connection planes
Offset Connection Tang Allows the terminal position to be adapted to the mating conductor and available installation space
Countersunk Mounting Features Supports recessed or flush fastener seating when the hole and screw-head geometries are correctly matched
One-Piece Construction Avoids a separately welded corner joint within the specified component
Near-Net Blank Option Can reduce material removal compared with machining the complete angle from solid block
Drawing-Based Hole Layout Allows mounting and connection holes to match the equipment interface
Controlled Contact Surfaces Enables flatness, roughness and coating requirements to be specified for the intended joint
Optional Surface Treatment Supports review of corrosion exposure, contact compatibility and assembly requirements

Manufacturing & Quality Control

Manufacturing Process

The process route is selected according to the material, terminal geometry, quantity and critical functional requirements.

Stage Process and Control
Drawing Review Confirm overall dimensions, offset, corner geometry, hole pattern, fastener details and mating contact areas
Material Selection Select the copper grade, temper and applicable starting-material specification
Near-Net Blank Preparation Where suitable, use extruded or cold-drawn L-section stock to limit machining allowance
CNC Profile Machining Use drawing-based copper machining support to finish the outline, connection tang, seating faces and clearance features
Hole Production Drill, bore, countersink or tap holes according to the specified fastener and assembly requirements
Geometric Finishing Control the relationship between the base, upright face and defined datum features
Deburring and Cleaning Remove burrs and machining residues while preserving the required contact areas and edge geometry
Surface Treatment Review optional copper component plating against the contact, fastener and environmental requirements
Final Protection Protect finished faces, hole edges and coatings during handling and shipment

Near-net profile production can reduce dependence on bending operations, but it does not remove the need to inspect angle accuracy, distortion and final dimensions.

Quality Control

Inspection methods, sampling frequency and acceptance criteria are agreed for each order. Further information is available on the quality assurance page.

Inspection Item Verification and Acceptance Basis
Material Identification Review the specified grade, material certificate and agreed batch identification
Chemical Composition Verify against the selected grade using suitable analytical methods; oxygen-content requirements need an appropriate dedicated method
Overall Dimensions Check length, width, height, thickness and offset against the approved drawing
Hole Diameter and Position Inspect through-hole sizes, center distances and positions relative to the specified datums
Countersunk Features Check angle, diameter, depth and remaining material against the selected fastener geometry
Perpendicularity Measure the relationship between base and upright surfaces using the agreed datum system
Contact-Face Flatness Inspect over the specified contact area using a suitable measurement method
Surface Condition Check contact-face roughness where specified and inspect for relevant burrs, dents or other defects
Conductivity and Hardness Test where ordered, with material condition, test method and acceptance values defined in advance
Coating Quality Verify the specified coating system, thickness, coverage and relevant functional requirements
Documentation Supply agreed material and dimensional records; EN 10204 3.1 documentation or third-party inspection requires advance confirmation

Component inspection does not replace assembly-level checks for contact resistance, temperature rise, fastening performance or short-circuit withstand.

Typical Applications

The following are potential drawing-matched applications, not universal equipment compatibility claims.

Application Typical Use Design Considerations
Circuit Breaker Connections Right-angle transition terminals for specified breaker inlet or outlet connections Terminal compatibility, fastener access, contact pressure and verified temperature rise
Power Contactors Fixed connection lugs for main-circuit terminals Hole layout, contact area, installation torque and operating duty
Switchgear Busbar Assemblies Compact conductive transitions between perpendicular busbar planes Minimum conductive section, support arrangement and equipment clearances
EV Power Distribution Units Drawing-specific copper links within distribution or inverter assemblies Vibration, joint retention, thermal cycling and insulation coordination
Power Conversion Equipment Offset connection terminals for inverter and energy storage assemblies Continuous current, duty cycle, cooling conditions and mating-conductor design
Transformers and Welding Equipment Custom bolted copper connections in restricted installation spaces Operating temperature, AC effects, mechanical loads and connection maintenance

FAQ

What is an L-shaped copper terminal lug?

It is a solid conductive component used to connect mating conductors on perpendicular planes. Unlike a cable-crimp lug, this design uses bolted interfaces rather than a barrel crimped around a cable. Its dimensions and hole layout are matched to the equipment drawing.

Can the offset, hole pattern and terminal dimensions be customized?

Yes. Overall dimensions, tang offset, thickness, hole sizes and contact surfaces can be reviewed against the mating assembly. The complete geometry must be checked together, including corner section, fastener access and remaining material around the holes.

Which copper grades can be specified?

C11000, C10200 and C10100 can be considered according to the required conductivity, material condition and processing route. Silver-bearing copper or CuCrZr requires a separate review because conductivity, strength and temperature behavior differ from pure copper.

Will countersunk holes make the screw heads flush?

They can when the screw-head angle, diameter and countersink depth are correctly matched. Remaining material and tightening loads must also be checked. A flush head does not by itself establish adequate electrical clearance or creepage distance.

Why use a near-net L-section blank?

A suitable near-net blank can reduce machining allowance compared with producing the complete angle from solid block. It may also avoid a bending step. However, material condition, corner geometry, dimensional accuracy and the economic benefit depend on the specific drawing and quantity.

Are the listed tolerances available on every size?

No. They are selected-feature enquiry targets. Feasibility depends on part dimensions, material, fixturing, surface treatment and inspection method. The drawing should identify critical datums and state whether dimensions apply before or after coating.

Can the terminal be silver, tin or nickel plated?

These finishes can be reviewed according to the connection and environment. Specify coating type, thickness, coverage, masking and any relevant contact requirements. Coating selection should consider the mating conductor, fasteners and installation conditions.

What current and voltage can the terminal handle?

No universal rating can be assigned from its shape or copper grade. Current capacity depends on the conductive section, joint resistance, cooling and permissible temperature rise. Voltage suitability depends on the complete insulation and clearance arrangement, supported by applicable equipment verification.

Request a Quote

Please provide a dimensioned drawing and the mating-interface details for technical review.

Required Information Details to Provide
Drawing Dimensioned PDF and, where available, a STEP or other suitable CAD file
Material Copper grade, applicable material standard and required temper
Overall Geometry Length, width, height, base thickness, upright thickness and offset
Hole Pattern Hole diameters, positions, center distances and any tapped features
Fastener Details Screw size, head style, countersink angle, seating depth and installation torque
Contact Requirements Mating conductor, contact area, flatness, roughness and coating requirements
Operating Conditions Current duty, ambient temperature, vibration and relevant mechanical loads
Surface Treatment Bare copper or specified coating system, thickness, coverage and masking
Inspection Critical tolerances, tests, inspection frequency and documentation
Quantity Prototype quantity, batch quantity and expected repeat demand
Delivery Requirements Destination country, packaging requirements and requested delivery schedule

Contact Cymber Metal with your drawing, quantity and application details to request a technical review and quotation.


  • Previous:
  • Next:

  • Write your message here and send it to us