Cold-Drawn Stepped T-Profile Pure Copper Bar

Short Description:

Item Specification
Product Type Stepped T-profile copper bar with rectangular tenon and bilateral flanges
Material Options C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, or TU2, specified under the selected material standard
Alternative Alloys C10400/C10700 silver-bearing copper or C18150 CuCrZr may be reviewed separately; properties differ from pure copper
Applicable Standards ASTM B187/B187M or EN 13605 where applicable to the grade and product form; other specifications by agreement
Overall Width Indicative enquiry range: 6–180 mm
Overall Height Indicative enquiry range: 4–90 mm
Tenon Width Indicative enquiry range: 2.5–120 mm
Flange Thickness Indicative enquiry range: 1–25 mm
Flange Configuration Equal or unequal side widths, according to drawing
Cut Segment Length Approximately 15–1,500 mm
Straight Bar Length Approximately 1,000–6,000 mm
Coil Supply Subject to section size, temper, bend radius, and production feasibility
Tenon Width and Flange Thickness Tolerance Indicative target: ±0.015–0.03 mm on agreed features
Top-to-Bottom Parallelism Indicative target: ≤0.02 mm over a specified measurement span
Straightness Indicative target: ≤0.25 mm/m under an agreed measurement method
Internal Root Radius Indicative target: 0.15–0.25 mm, subject to tooling and section geometry
Surface Roughness Indicative target: Ra 0.2–0.4 μm on designated surfaces
Temper H02, H04, O60, or another agreed condition where applicable
Hardness Indicative 85–125 HV for selected work-hardened conditions; not applicable to every grade or temper
Electrical Conductivity Grade- and temper-dependent; a target such as ≥98% IACS requires confirmation for the selected material
Surface Options Cleaned copper, bright finish, anti-tarnish treatment, silver plating, tin plating, or nickel coating
Secondary Processing Cutting, drilling, tapping, milling, chamfering, deburring, and application-specific finishing

Product Detail

Product Tags

Video

Short Description

The stepped T-profile copper bar combines a longitudinal rectangular tenon with a broad base and two side shoulders. Designed for drawing-based assemblies, this section can support keyed positioning, conductor mounting, and custom thermal-management components.

Material options include C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, and TU2, with the grade and temper selected according to the applicable specification. Extrusion and cold drawing can be combined with straightening, cutting, CNC machining, and optional surface treatment.

Flange widths, tenon dimensions, cut lengths, tolerances, and inspection requirements are confirmed against the customer drawing.

Stepped T-Profile Copper Bar Overview

A stepped T-profile copper bar is a solid copper section with a rectangular longitudinal rib and lateral shoulders. Depending on its installation orientation, it may function as a raised-rib conductor profile or an inverted T-section seated in a matching groove.

The tenon can assist lateral positioning when paired with a correctly dimensioned mating slot. The shoulders can provide seating surfaces or assembly stops. Equal or unequal flange widths may be specified to suit the available installation space.

Cymber Metal’s pure copper products provide the material starting point. For repeat production, custom copper profile extrusion and subsequent drawing can be reviewed as alternatives to machining the entire section from rectangular stock.

These processes may reduce material removal, but dimensional stability, straightness, and material utilization depend on the actual section and production route.

Key Features

Feature Practical Value
Longitudinal rectangular tenon Provides a defined locating feature for a matching groove or slot
Bilateral shoulders Creates seating surfaces for drawing-based assemblies
Equal or unequal flanges Allows the profile to accommodate symmetric or restricted mounting spaces
Integral copper section Combines the rib and base in one continuous conductive component
Custom profile forming Can reduce extensive stock removal where section geometry and production volume justify tooling
Cut-to-length supply Supports assembly planning and reduces downstream cutting
Secondary machining Allows holes, threads, slots, and local contact surfaces to be added
Optional surface treatment Supports application-specific contact and environmental requirements

Manufacturing & Quality Control

Manufacturing Process

Stage Process Description Main Control
Drawing Review Review tenon width, shoulder geometry, datums, mating clearance, and operating conditions. Confirm manufacturability and critical features
Material Selection Select the copper grade and condition for electrical, thermal, mechanical, and joining requirements. Confirm grade, standard, and temper
Profile Forming Use extrusion and controlled cold drawing where suitable for the section and order quantity. Control rib position, flange dimensions, and profile consistency
Condition Adjustment Apply the agreed work-hardened or annealed condition. Verify hardness and dimensional effects
Straightening and Cutting Straighten the profile and cut it into bars or finished segments. Check straightness, length, squareness, and burrs
Secondary Processing Add holes, threads, slots, chamfers, or precision faces through copper machining support. Inspect features against drawing datums
Surface Treatment Apply cleaning, anti-tarnish treatment, or specified coatings where required. Confirm coating coverage and assembly compatibility
Protection and Packing Separate and protect finished pieces for transport. Reduce scratching, deformation, and moisture exposure

Quality Control System

Inspection Item Method or Documentation Acceptance Basis
Material Identity and Composition Material certificate and appropriate chemical analysis Selected grade and purchase specification
Oxygen Content, When Specified Suitable oxygen-analysis method and supporting certificate Optical emission spectroscopy alone is not proof of low oxygen content
Profile Geometry Optical measurement, profile projector, micrometers, or CMM Tenon width, flange width, thickness, and rib position
Parallelism and Perpendicularity Datum-based CMM or suitable fixture inspection Drawing tolerances and defined measurement span
Straightness Surface plate, straightedge, gauges, or coordinate measurement Agreed support arrangement and measurement length
Surface Finish and Edges Profilometer where required, plus visual inspection Designated roughness, burr limits, and permitted surface condition
Conductivity and Hardness Agreed conductivity and hardness tests Material condition and specified acceptance values
Assembly Fit Sample assembly or dedicated profile gauge Mating clearance, insertion, and seating requirements
Coating, When Ordered Thickness and coverage checks Agreed coating specification
Traceability and Reports Heat/lot identification and inspection records Documentation scope agreed before production

Inspection frequency and any nondestructive testing should be agreed before ordering. EN 10204 3.1 certificates and third-party inspection are subject to the applicable supply arrangement.

See the Quality Assurance page for inspection and documentation enquiries.

Typical Applications

Application Typical Use Design Considerations
Switchgear and Breakers Located conductor bars or stationary contact supports Current, temperature rise, clearances, fastening, and short-circuit forces
Contactors and Conductor Tracks Keyed copper rails or contact-support profiles Contact pressure, wear, surface finish, and coating selection
Busway Assemblies Profiled conductors seated in matching supports Insulation, thermal expansion, support spacing, and fit
Liquid Cold Plates Stepped cover strips or locating inserts in purpose-designed assemblies Copper grade, joining procedure, distortion, corrosion compatibility, and leak testing
Inverters and Energy Storage Equipment Custom conductive or thermal-interface components Electrical isolation, temperature, joint resistance, and assembly tolerances
Motors and Generators Drawing-specific slot components considered by the equipment designer Mechanical strength, fatigue, speed, temperature, and electromagnetic requirements

For joining-sensitive projects, C10200 copper may be considered, but material selection alone does not qualify a welding or brazing procedure. Weld zones should have a specified surface condition rather than an assumed plating requirement.

Cold-plate sealing and rotating-machine applications require separate engineering validation. This profile does not carry a universal current, pressure, or rotational-speed rating.

FAQ

Can the two flanges have different widths?

Yes. Equal or unequal flange widths can be reviewed from the drawing. Unequal widths may help accommodate restricted space or distinguish assembly orientation when the mating geometry also provides that function.

Is it different from a conventional inverted T copper bar?

The basic geometry is related. This version emphasizes controlled shoulder dimensions and a rectangular locating tenon. Installation orientation determines whether the rib faces upward or enters a mating slot.

What is a stepped T-profile copper bar?

It is a copper section with a longitudinal rectangular tenon and two side shoulders. The tenon can locate within a matching groove, while the shoulders provide defined seating surfaces.

Which copper grade should be selected?

Selection depends on conductivity, temper, joining conditions, temperature, and mechanical loading. C11000 and oxygen-free grades such as C10200 are options, but they are not interchangeable for every manufacturing process.

Can this profile be used as a cold-plate cover strip?

It can be reviewed for a purpose-designed cover or insert. The assembly still requires a qualified joining procedure, dimensional control, corrosion review, and appropriate pressure or leak testing.

Can holes, threads, or plating be added?

Yes. Machining and coating requirements can be included in the RFQ. Specify feature positions, tolerances, coating type, thickness, and any areas that must remain uncoated.

Are the listed precision tolerances guaranteed?

No. They are enquiry targets. Achievable values depend on section size, length, temper, tooling, finishing, and inspection method, and must be confirmed before production.

What is needed for a quotation?

Provide the drawing, grade, standard, temper, dimensions, tolerances, quantity, surface treatment, application, inspection requirements, destination, and target schedule. A mating drawing is useful for keyed assemblies.

Request a Quote

Required Information Details to Provide
Material and Standard Grade, governing specification, temper, conductivity, and hardness requirements
Drawing Dimensioned 2D drawing, 3D model, or sample; include mating geometry where available
Section Dimensions Overall width and height, tenon width, flange widths, thicknesses, and root radii
Tolerances Critical dimensions, datums, parallelism, straightness, and measurement span
Supply Form and Quantity Cut segments, straight bars, or coil enquiry; prototype and batch quantities
Processing and Surface Holes, threads, slots, finish, coating, coverage, and uncoated zones
Application and Documents Operating conditions, inspection plan, material certificate, and any compliance documents
Delivery Requirements Destination, Incoterm, packaging, and requested schedule

Contact Cymber Metal for a drawing-based quotation. The section, production route, inspection plan, and commercial terms will be reviewed against your requirements.


  • Previous:
  • Next:

  • Write your message here and send it to us