Curved-Tip Copper Contact Blade with Countersunk Holes

Short Description:

Item Specification
Product Custom curved-tip copper contact blade with countersunk mounting holes
Photographed Configuration Single upturned end, four countersunk holes on one face, rounded longitudinal edges
Primary Material Options C11000 ETP copper; C10200 oxygen-free copper; C10100 oxygen-free electronic copper
Alternative Materials C10400/C10700 silver-bearing copper or C18150 CuCrZr, subject to separate conductivity, wear and processing review
Starting-Material Standards ASTM B187/B187M for applicable bar stock or ASTM B152/B152M for applicable sheet/strip stock; other standards by agreement
Length Indicative range: 30–1200 mm
Width Indicative range: 8–120 mm
Thickness Indicative range: 3–25 mm
Lead-In Tip Single-end or drawing-specific double-end curved profile; angle, rise and transition radius specified by drawing
Edge Geometry Rounded longitudinal edges and radiused ends; exact radii defined by drawing
Hole Pattern Custom quantity, diameter and pitch; photographed sample has four mounting holes
Countersink Options Drawing-specific 90°, 100° or 120° included angles matched to the nominated screw
Other Mounting Options Counterbores or rear tapped holes, where thickness and design permit
Selected Hole-Location and Depth Targets ±0.02–0.04 mm, subject to feature-specific review
Straightness and Flatness Proposed local target: 0.03 mm over an agreed 100 mm evaluation length; overall requirements specified separately
Selected Contact-Face Roughness Proposed target: Ra 0.2–0.4 μm
Material Condition Half-hard or hard condition where suitable; temper designation follows the applicable material specification
Hardness A 90–125 HV target may be reviewed against grade, forming requirements and final condition
Conductivity A target of ≥98% IACS may be specified for suitable pure-copper grades and conditions, with agreed testing
Surface Finish Bare copper, compatible anti-tarnish treatment, or specified silver, tin or nickel plating
Silver-Plating Option An indicative 10–30 μm thickness may be reviewed; deposit type, hardness, undercoat and coverage require specification

Product Detail

Product Tags

Video

Short Description

Cymber Metal supplies custom copper contact blades with an upturned lead-in tip, rounded edges and countersunk mounting holes. The photographed version features four conical countersinks on one face and a single curved end. Compatible countersunk screws can be seated flush with or below the specified face, subject to fastener and hole geometry. Material options include C11000 ETP copper, C10200 oxygen-free copper and C10100 oxygen-free electronic copper. Dimensions, tip profile, hole pattern and optional contact finishes are tailored to customer drawings for switchgear and other engineered electrical contact assemblies.

Copper Contact Blade Overview

A copper contact blade is a conductive bar or strip used as part of an electrical contact assembly. This curved-tip version combines a longitudinal contact face with an upturned entry end and recessed mounting features.

The photographed component has four countersunk holes, rounded long edges and a curved tip at one end. Its opposite face shows the corresponding through-holes without the large conical recesses.

The upturned end provides a lead-in geometry that can be matched to a moving contact or mating assembly. Countersunk mounting allows suitable screw heads to sit at or below an agreed surface level. Together, these features can support compact installation where projecting fasteners would interfere with nearby components.

Sliding performance still depends on the complete contact system. Contact pressure, alignment, mating material, coating, lubrication where permitted, and the location of mounting interruptions must be reviewed together.

Cymber Metal supports drawing-based selection from its pure copper material range. Where an oxygen-free grade is required, C10200 copper is one option for technical review.

Key Features

Feature Practical Value
Curved Lead-In Tip Provides an entry profile that can be matched to the mating contact geometry
Countersunk Mounting Holes Allows compatible screws to sit flush with or below a specified surface level
Four-Hole Sample Configuration Provides multiple fixing locations; spacing and quantity can be customized
Rounded Longitudinal Edges Reduces sharp-edge handling risks and supports controlled edge geometry
Drawing-Specific Contact Face Allows contact zones, surface finish and mounting interruptions to be defined together
Copper Grade Options Supports selection according to conductivity, processing and service requirements
Optional Contact Plating Allows surface properties to be matched to the mating material and contact duty
Custom Tip and Hole Geometry Accommodates equipment-specific mounting and engagement requirements

Rounded edges do not eliminate electrical discharge, and multiple screws do not establish a short-circuit withstand rating. These aspects require assembly-level engineering and verification.

Manufacturing & Quality Control

Manufacturing is planned around the required contact geometry, screw seating, material condition and final surface finish.

Manufacturing Process

Stage Process and Control Focus
Drawing Review Confirm contact zones, mounting datums, tip geometry, screw specification and required fastener clearance
Material and Temper Selection Select suitable copper stock and condition against conductivity, forming and mechanical requirements
Blank Preparation Cut suitable flat bar or strip; rounded-edge drawn stock may be considered where appropriate
Tip Forming Form the curved end using a suitable radius and material condition; review springback and local deformation
Drilling and Countersinking Produce the hole pattern and conical seats with controlled location, angle and depth
Double-Side Deburring Remove entry and exit burrs without changing the specified screw seats or supporting face
Contact-Face Finishing Finish designated contact areas to the agreed roughness and geometry
Optional Plating Apply the specified finish, allowing for coating thickness at screw seats and contact interfaces
Protection and Packing Protect contact surfaces and separate parts to reduce scratching during handling and shipment

Hole patterns, countersinks and selected contact faces can be reviewed through our custom copper machining services. Optional finishing routes are introduced on our busbar plating page.

Quality Control and Inspection

Inspection Item Method and Acceptance Basis
Material Identity Review material documents and use grade-appropriate composition verification where required
Oxygen-Free Requirements Confirm oxygen-related requirements using appropriate certificates or dedicated testing, rather than routine composition screening alone
Electrical Conductivity Use an agreed method with suitable calibration, temperature control and allowance for part geometry
Hardness Test at agreed locations where hardness is specified; account for changes associated with forming
Overall Dimensions Inspect length, width, thickness and mounting references against the drawing
Hole Pattern Check diameter, location, pitch and alignment to the agreed datums
Countersink Geometry Inspect included angle, major diameter and depth against the nominated screw geometry
Screw-Head Seating Check actual nominated screws for head projection or recess, including relevant fastener and coating tolerances
Curved Tip Inspect tip rise, angle, transition radius and alignment
Contact and Supporting Faces Check specified straightness, flatness and roughness over defined evaluation areas
Surface Condition Inspect holes, edges and formed regions for unacceptable burrs, cracks or damage
Coating Verify specified thickness, coverage and order-specific coating requirements
Functional Validation Agree mating-contact, wear or electrical tests where required; these are separate from dimensional inspection
Documentation Define material records, traceability, dimensional reports and any third-party inspection before production

Inspection scope and sampling frequency are agreed for each order. EN 10204 3.1 documentation, where required and applicable, must be confirmed before ordering.

Visit our quality assurance page for further information on inspection and quality management.

Typical Applications

The following are potential applications for drawing-specific versions. Suitability must be established by the equipment manufacturer.

Application Typical Use Design Considerations
Switchgear Contact Assemblies Conductive contact bars with recessed mounting Contact pressure, mating geometry, temperature rise and insulation coordination
Disconnectors and Earthing Switches Blade or contact-strip components with shaped entry ends Engagement path, alignment, operating force and contact resistance
Circuit-Breaker Assemblies OEM-specified conductive bars or stationary contact components Electrical duty, mounting strength, heat rise and equipment-level testing
Sliding or Plug-In Contacts Contact strips with controlled lead-in geometry Wear, surface finish, plating, contact continuity and mounting-hole interruptions
Transformer Tap-Changer Mechanisms Drawing-specific contact-track components Switching medium, erosion, contact force and OEM qualification
Specialized Arc-Management Assemblies Arc-runner geometry manufactured to a validated OEM design Arc transfer, erosion, material selection and complete interruption testing

A curved copper tip alone does not establish arc-running, arc-extinguishing or breaking capacity. Those functions depend on the complete device.

Frequently Asked Questions

What is this copper contact blade used for?

It is a drawing-specific conductive component for electrical contact assemblies. The curved end provides a shaped entry profile, while countersunk holes accommodate recessed mounting screws. Whether it serves as a stationary contact, blade or contact track depends on the equipment design.

What is the purpose of the upturned tip?

The tip provides a gradual entry geometry that can be matched to a moving contact or mating component. Its effect on engagement force and wear depends on tip angle, radius, alignment, contact pressure and surface finish. These factors should be verified together.

Will the screw heads sit completely below the contact face?

They can when screw-head dimensions, countersink angle, diameter and depth are correctly matched. Coating thickness and fastener tolerances also matter. Final seating should be checked with nominated screws; countersinking alone does not guarantee a completely unobstructed sliding path.

Can this component function as an arc runner?

A drawing-specific version may form part of an OEM-designed arc-management assembly. However, the photographed shape does not demonstrate arc-transfer or interruption performance. Arc-runner suitability requires review of the complete device, operating duty, material and relevant test results.

Which copper grade should be selected?

C11000 is ETP copper, while C10200 and C10100 are oxygen-free grades with different specification requirements. Selection depends on conductivity, forming, thermal conditions and documentation needs. Silver-bearing copper and CuCrZr require separate review rather than being treated as direct substitutes.

Is silver plating recommended for sliding contacts?

Silver plating may be appropriate, but its composition, hardness, thickness and undercoat must match the contact duty. Mating materials, contact pressure, wear and environment also affect performance. Tin and nickel finishes should not be assumed to provide equivalent sliding-contact behavior.

What current and voltage can the blade handle?

There is no universal rating based on its outline or copper grade. Current capacity depends on section, contact resistance, cooling and permissible temperature rise. Voltage suitability depends on insulation, clearances, creepage and the complete equipment design.

What information is needed for a quotation?

Provide the drawing, material grade and condition, dimensions, quantity, tip geometry, hole pattern, nominated screws and surface treatment. Include contact duty, operating conditions, critical tolerances, inspection documents, destination and requested delivery schedule.

Request a Quote

Required Information Details to Provide
Drawing Dimensioned 2D drawing and, where available, a 3D model
Material Copper grade, standard, temper and required conductivity or hardness
Overall Dimensions Length, width, thickness and dimensional datums
Curved Tip Tip rise, included angle, transition radius and single- or double-end configuration
Mounting Holes Quantity, diameter, pitch, countersink angle and depth
Fasteners Screw standard, size, head geometry and permitted head projection or recess
Contact Requirements Contact zones, mating material, contact pressure and sliding or switching duty
Surface Finish Roughness, coating type, thickness, coverage and masking
Quantity Prototype quantity, batch quantity and estimated annual usage
Inspection Critical dimensions, functional tests and required reports or certificates
Delivery Destination, packaging requirements and requested schedule

Contact Cymber Metal for a drawing-based quotation for your custom curved-tip copper contact blade.


  • Previous:
  • Next:

  • Write your message here and send it to us