L-Shaped Copper Flange Busbar Connector

Short Description:

Item Specification / Enquiry Reference
Product L-shaped copper flange busbar connector
Product Form Custom finished conductive component
Material Options C11000 ETP, C10200 oxygen-free or C10100 oxygen-free electronic copper, subject to order confirmation
Material Specification Selected by grade and starting form; examples include ASTM B187/B187M for applicable electrical copper bar and ASTM B152/B152M for applicable plate
Horizontal Arm Length 40–350 mm, subject to drawing review
Width 25–200 mm, subject to drawing review
Vertical Flange Height 30–220 mm, subject to drawing review
Thickness 4–35 mm, subject to material and forming feasibility
Central Bore Indicative diameter Ø12–150 mm; H7/H8 fits may be reviewed where specified
Flange Hole Pattern Eight holes on the photographed design; alternative patterns reviewed by drawing
Horizontal Connection Pad Stepped outline with four cylindrical counterbores on the photographed design
Hole-Location Targets Selected coordinate dimensions may be reviewed at ±0.02–0.04 mm; GD&T position requirements must be defined separately
Perpendicularity Target 0.03 mm where feasible, with datum, evaluated surface and measurement extent specified
Contact-Face Flatness Target 0.02 mm on selected faces, subject to size, thickness and finishing route
Surface Roughness Target Ra 0.4–0.8 μm on designated machined faces, subject to confirmation
Conductivity Requirement A target of ≥98% IACS may be specified for suitable pure-copper grades and conditions
Hardness Requirement A target range of 85–120 HV may be reviewed against the selected material condition and forming route
Surface Options Bare copper, compatible anti-tarnish treatment, or specified silver, tin or nickel plating
Plating Thickness Drawing-specific; silver thickness of 5–30 μm may be discussed where appropriate
Final Acceptance Approved drawing, material specification and agreed inspection plan

Product Detail

Product Tags

Video

Short Description

Custom L-shaped copper flange busbar connector featuring an upright flange with a central bore and mounting-hole circle, combined with a stepped horizontal connection pad. The photographed design has eight flange mounting holes and four cylindrical counterbores on the pad. Material grade, bore fit, hole pattern, contact-face finish and optional plating are specified to match the approved drawing and mating assembly.

Copper Flange Busbar Connector Overview

A copper flange busbar connector provides a right-angle transition between a flange-mounted conductive interface and a flat busbar connection. Its upright flange and horizontal pad allow the two interfaces to be positioned on perpendicular planes.

The photographed component combines a large central bore, an eight-hole flange pattern, a stepped pad outline and four recessed fastening positions. The bore’s function—clearance, location or another specified fit—depends on the assembly drawing; the bore alone does not establish a clamping connection.

Cymber Metal supports drawing-based component review using suitable pure copper materials, including C11000 ETP copper and C10200 oxygen-free copper. Final material, manufacturing route and inspection requirements are confirmed for each project.

Key Features

Feature Product Detail
Right-Angle Connection Geometry Upright flange and horizontal pad support a perpendicular conductive transition within the customer’s assembly.
Central Bore and Bolt Circle Bore size, fit and mounting-hole positions can be defined around the mating conductor or flange interface.
Recessed Pad Fastening Cylindrical counterbores accommodate specified fastener heads when pocket depth, screw dimensions and coating allowance are coordinated.
Stepped Pad Outline Shoulder position, pad width and outer contour can be adapted to the approved assembly envelope.
Drawing-Based Contact Faces Flatness, roughness and coating requirements can be assigned specifically to electrical contact surfaces.

Manufacturing & Quality Control

The manufacturing route and inspection scope are established after reviewing the drawing, material condition and critical assembly requirements.

Manufacturing Process

Stage Process and Control
Material Selection Select suitable copper grade, stock form and condition; review material documentation against the purchase specification.
Blank Preparation and Forming Prepare the blank and, where the selected route uses forming, establish the right-angle geometry before final machining of critical interfaces. Bend radius and forming conditions require engineering review.
CNC Machining Use appropriate copper machining support for the central bore, flange mounting holes, pad counterbores, stepped contour and designated contact faces.
Deburring and Cleaning Remove machining burrs, apply specified edge breaks and clean holes and contact surfaces before inspection or coating.
Surface Treatment Review masking, coating system and thickness through the applicable busbar plating process. Account for coating effects on fits and recessed fasteners.
Final Protection Select packaging to protect machined faces, hole edges and finished surfaces during handling and transport.

Inspection and Quality Control

Inspection methods, sampling and documentation should be agreed before production. Further information is available on our quality assurance page.

Inspection Item Verification Approach
Material Identity Review grade and heat/batch documentation; arrange appropriate composition testing when specified. Oxygen-content requirements need a suitable method rather than an assumption from general elemental screening.
Conductivity and Hardness Verify specified properties using agreed methods, material condition, temperature reference and sampling requirements.
Bore and Hole Dimensions Use suitable bore gauges, pin gauges or coordinate measurement for agreed diameters, fits and counterbore dimensions.
Hole Pattern and Orientation Check bolt-circle geometry, pad-hole locations and flange-to-pad orientation against the drawing datum system.
Contact Faces Measure specified flatness and roughness using suitable equipment and evaluation conditions.
Formed Region Perform visual examination and, when required, an agreed penetrant or suitable ultrasonic inspection procedure. NDT scope and acceptance criteria must be defined.
Coating Check specified coating thickness, coverage, masking and applicable adhesion requirements.
Traceability and Reports Agree batch identification, dimensional reports and material documentation, including EN 10204 3.1 documentation where required and applicable.

Typical Applications

These are potential applications requiring confirmation of the mating design, operating conditions and OEM acceptance.

Application Typical Use Design Considerations
Vacuum Circuit Breaker Assemblies Conductive transition between a terminal-side flange interface and a flat connection pad Terminal arrangement, mounting loads, temperature rise, contact design and equipment qualification
GIS and Ring Main Units Custom flange-to-busbar connections within an approved switchgear design Electrical clearances, gas-system compatibility where relevant, coating and assembly tolerances
Air Circuit Breakers and Disconnectors Right-angle connections between defined conductive interfaces Fastener preload, thermal cycling, contact pressure and electrodynamic loading
Transformer Bushing Connections Transition from a bushing-side interface to a flat busbar Bushing loads, interface fit, allowable movement and contact-face requirements
Industrial Power Equipment Drawing-specific copper adapters for perpendicular conductor layouts Available space, cooling, mechanical support and operating duty

FAQ

What is a copper flange busbar connector?

It is a conductive transition component combining a flange-style interface with a flat busbar connection. This design places the two interfaces at approximately 90 degrees.

Which copper grades can be considered?

C11000 ETP, C10200 oxygen-free and C10100 oxygen-free electronic copper can be reviewed. Grade selection depends on the electrical, mechanical, thermal and manufacturing requirements. These grades are not automatically interchangeable.

Are the eight flange holes and four pad counterbores fixed?

They describe the photographed component. Different hole counts, bolt-circle diameters, bore sizes and pad layouts can be reviewed against a customer drawing.

Does the central bore clamp a cylindrical conductor?

Not necessarily. A bore may provide clearance, location or a specified fit. Any gripping or clamping function requires a defined assembly, mating dimensions and fastening arrangement.

Can tight bore and hole-position tolerances be specified?

Yes, as drawing requirements for feasibility review. Bore fits, coordinate tolerances and GD&T position tolerances must be defined correctly, with appropriate datums and inspection conditions.

Will the screw heads sit flush inside the counterbores?

Only when the specified fastener head, counterbore diameter, recess depth and coating allowance are compatible. A recessed hole alone does not guarantee flush seating.

Can the connector be silver-, tin- or nickel-plated?

These finishes can be reviewed. The order should identify the coating system, thickness, contact areas, masking boundaries and any adhesion or environmental requirements.

What current or voltage rating does the connector have?

No universal rating can be assigned from the photographs or shape alone. Suitability depends on conductor dimensions, contact resistance, cooling, insulation clearances, mechanical loads and validation of the complete equipment assembly.

Request a Quote

Required Information Details to Provide
Drawing Dimensioned 2D drawing, revision and available 3D model
Material Grade, standard, condition, conductivity and hardness requirements
Critical Geometry Bore fit, bolt circle, counterbores, contact faces, datums and tolerances
Assembly Mating components, fasteners, installation loads and application
Operating Conditions Current, duty cycle, temperature limits and relevant equipment requirements
Surface Treatment Coating type, thickness, masking and contact-surface requirements
Inspection Required reports, traceability, sampling, certificates and third-party inspection
Purchasing Details Quantity, repeat demand, destination, packaging and requested delivery date

Contact Cymber Metal for a drawing-based quotation covering material selection, machining feasibility, surface treatment and inspection requirements.


  • Previous:
  • Next:

  • Write your message here and send it to us