Custom Copper Conductor Link Rod with Flat Mounting Lugs
Video
Short Description
A custom copper conductor link rod with a long round shaft and a flattened mounting lug at each end. The photographs show one hole in each lug and a smooth, silver-colored surface.
Specify the copper grade, temper, overall length, shaft diameter, lug dimensions, hole configuration and surface finish according to the drawing and order requirements.
Product Description
This custom copper conductor link rod is designed with a round central shaft and flat mounting lugs at both ends. The supplied product notes describe one locating hole at one end and an axial adjustment slot at the other. Confirm the final hole shapes, dimensions and orientation against the approved drawing.
The product notes identify the material as copper, but the exact grade and temper should be confirmed for each order. Dimensions, tolerances, surface finish and any coating requirements are also subject to drawing review. For general material information, see our Pure Copper page. Drawing-based machining requirements can be reviewed through Fine Machining.
Key Features
- Round-shaft profile with flat mounting lugs at both ends.
- End-hole configuration can be defined by drawing.
- Lug orientation and dimensions can be specified for the intended assembly.
- Material grade, tolerances and surface finish should be confirmed for each order.
- A drawing-based RFQ supports review of hole alignment and manufacturing feasibility.
Typical Applications
| Application | Possible Use |
|---|---|
| Switchgear | Conductor link within a custom busbar assembly |
| GIS Equipment | Connection rod for a drawing-specific electrical assembly |
| Disconnectors and Earthing Switches | Conductor connection where the equipment design calls for a link rod |
| Power Distribution Assemblies | Custom connection between electrical components |
| Renewable Energy Equipment | Conductor link in an assembly, subject to electrical and mechanical review |
Application suitability depends on the complete assembly design, including current, temperature rise, clearances, insulation, mechanical loading and applicable equipment requirements. These details should be reviewed by the project engineer.
Typical Manufacturing Process
The process below is indicative. The actual route depends on the drawing, grade, order quantity and required finish.
| Step | Process | Details to Confirm |
|---|---|---|
| 1 | Material Selection | Confirm copper grade, temper, standard and required documents |
| 2 | Bar Preparation | Confirm shaft diameter, blank length and straightness requirements |
| 3 | End-Lug Processing | Confirm lug dimensions, profile and orientation |
| 4 | Hole Machining | Confirm round-hole and slot details, positions and tolerances |
| 5 | Deburring and Finishing | Specify edge condition, surface finish and any required coating |
| 6 | Final Inspection and Packing | Check agreed dimensions and appearance; confirm packaging requirements |
Manufacturing & Quality Control
| Control Point | Review Approach |
|---|---|
| Material | Confirm grade and temper against the order specification and required material records |
| Shaft | Check diameter, length and straightness against the drawing |
| End Lugs | Check dimensions, profile, orientation and alignment |
| Hole Pattern | Verify hole shape, size, position and orientation against the drawing |
| Surface and Edges | Inspect for visible damage or burrs according to the agreed finish |
| Final Documentation | Confirm required inspection records and material documents at order placement |
For information about inspection methods and available documentation, see Quality Assurance. Product-specific tests, tolerances and documents should be agreed before ordering.
Frequently Asked Questions
It is a conductor component with a long shaft and connection features at both ends. This pictured design has a round central section and flattened mounting lugs with a hole at each end.
The supplied product notes describe one round locating hole and one axial adjustment slot. Confirm this configuration against the drawing, including the slot length, width, position and orientation.
The supplied product notes identify the material as copper but do not verify a specific grade for this pictured part. Confirm the required grade, temper, standard and material-document requirements in the RFQ.
The photographs show a silver-colored surface but do not identify the coating. If plating is required, specify the coating metal, thickness and any areas that need masking.
The lug profile, hole positions and orientation should be dimensioned on the drawing. Any angle between the end lugs should also be specified and reviewed before production.
Please provide the copper grade and temper, drawing, overall length, shaft diameter, lug and hole details, tolerances, finish, quantity, application, required documents and destination.
RFQ Information
| Please Provide | Details |
|---|---|
| Material | Copper grade, temper and material standard |
| Drawing | 2D or 3D drawing with dimensions and critical tolerances |
| Shaft | Overall length, diameter and straightness requirements |
| End Lugs | Width, thickness, profile and orientation |
| Holes | Round or slotted, size, position and orientation |
| Finish | Surface condition or specified surface treatment |
| Quantity | Sample quantity and production quantity |
| Application | Equipment type and relevant operating requirements |
| Documents | Material certificate, inspection report or other required records |
| Delivery | Destination country, packing requirements and target schedule |
Send your drawing and requirements to Cymber Metal through Contact Us for a material and manufacturing review.









